Winter Safety Checklist: Preparing Your Sites for Ice, Cold Stress, and Darker Shifts
By Infranoto
Daylight saving time ended this past weekend. For a lot of crews, that means the morning shift now starts in the dark and the evening shift ends in it. Within a few weeks, many sites will see their first frost on the parking lot, and the same pattern shows up in injury data almost every year: more slips and falls, more vehicle incidents, and a new set of hazards from heaters, closed-up buildings, and cold hands.
None of this is a surprise, which is exactly why it's worth planning for now. Here's a checklist to work through before the first hard freeze.
Slips and falls on snow and ice
Slips, trips, and falls are already one of the most common recordable injuries, and winter makes them worse. The highest-risk spots are usually outside the work area itself: parking lots, walkways, building entrances, dock aprons, and the steps up to equipment and vehicles.
OSHA's walking-working surfaces standard, 29 CFR 1910.22, specifically lists snow and ice among the hazards employers must keep walking surfaces free of. Before the weather turns:
- Assign snow and ice removal. Decide who clears and treats each area, when they do it (before shift start, not after), and who checks it. If a contractor handles the lot, confirm their response times in writing.
- Stock salt, sand, or ice melt near every entrance and dock, not just in the maintenance shop.
- Fix drainage problems now. Downspouts that empty onto walkways and low spots that collect water turn into ice sheets overnight.
- Put down entrance mats long enough to dry boots, and replace them when they're saturated. Melted snow tracked inside causes falls on smooth concrete and tile.
- Check handrails and steps on stairs, ramps, dock ladders, and vehicle and equipment access points. Three points of contact matters more when steps are icy.
- Remind crews about footwear. Slip-resistant soles, and traction cleats for people who work outdoors on ice. Cleats need to come off before walking on smooth indoor floors, where they become a slip hazard themselves.
- Teach the "penguin walk" in a pre-shift talk: short steps, feet slightly pointed out, center of gravity over your front foot, hands out of pockets. It sounds silly and it works. Our free slips, trips, and falls toolbox talk is a good five-minute starting point.
Cold stress
OSHA doesn't have a specific cold stress standard, but the General Duty Clause still requires employers to protect workers from recognized hazards, and OSHA's winter weather guidance spells out what that looks like. Utility line crews, yard workers, dock crews, and anyone working in unheated warehouses or freezers are most at risk.
The main conditions to train people to recognize:
- Hypothermia: shivering, confusion, slurred speech, drowsiness, and clumsiness. Severe shivering that stops is a bad sign, not a good one. Call for medical help and get the person somewhere warm.
- Frostbite: reddened skin that develops gray or white patches, along with numbness, tingling, or firm skin, most often on fingers, toes, ears, and the nose. Don't rub or massage the area, and don't try to rewarm it before getting medical help.
- Trench foot: caused by feet staying wet and cold for long periods, even at temperatures well above freezing. Watch for it in crews working in wet trenches, wash-down areas, or rain.
To prevent them:
- Watch wind chill, not just temperature. A 30°F day with a 25 mph wind is far more dangerous than it sounds. Check the forecast before outdoor work and adjust plans for extreme conditions.
- Schedule warm-up breaks in a heated space, and schedule outdoor work for the warmest part of the day when you can.
- Use the buddy system for outdoor and remote work. Early hypothermia causes confusion, so people often don't notice it in themselves.
- Dress in layers: a moisture-wicking base, an insulating middle, and a wind- and water-resistant outer layer. Keep spare gloves, socks, and liners available, because wet clothing loses most of its insulating value.
- Break in new and returning workers. People who haven't worked in the cold recently need time to adjust, just like with heat.
- Check PPE compatibility. Bulky winter gloves can make it harder to operate controls or keep a grip on tools. Make sure hard hat liners, face coverings, and insulated gloves work with the rest of the required PPE, including arc-rated gear for electrical work.
Carbon monoxide from heaters and equipment
Winter is when buildings get closed up. Dock doors stay shut, propane forklifts keep running, and someone brings in a portable heater to keep a work area warm. Carbon monoxide is colorless and odorless, and early symptoms like headache, dizziness, and nausea are easy to mistake for a cold or flu.
- Never use fuel-burning heaters, generators, or engines in enclosed spaces without adequate ventilation. That includes trailers, tents, and enclosed trenches.
- Tune up propane and gas-powered forklifts and floor equipment before the season, and check emissions. Poorly tuned engines produce much more CO.
- Install CO monitors in docks, warehouses, and maintenance areas where combustion equipment runs indoors.
- Inspect heating systems and make sure flues and exhaust vents are clear.
- Train crews on symptoms. If several people in the same area report headaches at the same time, treat it as possible CO exposure and get everyone into fresh air.
Darker shifts and vehicle traffic
With fewer daylight hours, more of the workday happens in the dark, often while people are tired from adjusting to the time change.
- Walk your site at shift change after dark. Check parking lots, walkways, yards, dock areas, and pedestrian routes for burned-out or inadequate lighting. Things look very different at 6 a.m. in November than they did on the summer audit.
- Upgrade high-visibility gear for anyone working near traffic or mobile equipment. Reflective material matters far more than color in low light.
- Review forklift and pedestrian separation in yards and docks, especially where trucks are backing in the dark. Our free forklift and pedestrian safety talk and loading dock safety talk cover the basics.
- Prepare company vehicles with winter tires where needed, working lights and wipers, and an emergency kit: blanket, flashlight, ice scraper, jumper cables, and a phone charger.
- Remind drivers to adjust. Slow down, increase following distance, and clear all snow and ice off the vehicle, including the roof.
Electrical and utility work in winter
For utility crews, winter storms often mean emergency restoration work under the worst possible conditions. Planning ahead helps:
- Review storm response procedures before the first big event, including fatigue limits for crews working long restoration shifts.
- Treat every downed line as energized until it's verified de-energized and grounded. Snow can hide downed conductors.
- Account for ice loading on lines and trees. Ice-loaded branches and lines can fail without warning.
- Brief crews on electrical safety and arc flash before storm season, not during it.
Use last winter's data
Your own incident history is the best guide to where this winter's injuries will happen. Before the season starts, pull last November through March and look for:
- Where slips and falls happened. If half of them were in the same parking lot or at the same entrance, that's where your ice control effort should go first.
- What shifts and times they clustered around. Early-morning falls before the lot is treated are a common pattern.
- Near-misses and hazard reports about ice, lighting, or heaters that never turned into injuries. Those are the ones to fix first. If you don't have many, it's a good time to build a near-miss program people will actually use.
Every injury you prevent this winter keeps your TRIR down and avoids costs that add up quickly. See what a single slip-and-fall really costs with the free Injury Cost Calculator, and check whether a winter injury is recordable with the OSHA Recordability Checker.
How Infranoto helps
Seasonal hazards are a good example of why safety data needs to be in one place:
- Hazard reports from the parking lot. QR codes at entrances, docks, and lots let anyone report an icy walkway in seconds, pre-filled with the location, even without a company login or a cell signal.
- Seasonal pattern detection. AI surfaces recurring hazards across incidents, near-misses, and observations, so the same icy entrance doesn't produce a fall every January.
- Corrective actions that get done. Assign the drainage fix or the lighting upgrade to an owner with a due date, and confirm it was done before the first freeze.
- Toolbox talks and sign-offs for winter topics, tracked across every crew and site.
See the full feature set on the platform page, or request a demo and we'll show you how to spot last winter's patterns in your own data.
The takeaway
- Plan for ice before it arrives. Assign removal, stock ice melt, fix drainage, and focus on parking lots, entrances, and docks.
- Train crews on cold stress symptoms, and use warm-up breaks, layers, and the buddy system.
- Watch for carbon monoxide whenever buildings are closed up and combustion equipment runs indoors.
- Walk your site in the dark and fix lighting and visibility gaps before someone gets hit.
- Use last winter's incident and near-miss data to decide where to focus first.